New oscilloscopes address expanding development needs

This article introduces a new series of oscilloscopes which feature all necessary functions to thoroughly test the behavior of complex embedded systems.

Figure 1. Directly addressing the need for a highly functional cost-effective T&M device, the RTC1000 oscilloscope series offers a compact eight-in-one instrument.


By Alix Paultre, Editor                                      Download PDF version of this article


Test & Measurement is arguably one of the most difficult disciplines to master in electronic design engineering. Your math must be good, and your imagination broad, to create a great design, but if you can’t dial that great design in and make it a viable product, you will die a penniless beggar (or worse, have to share credit with your buddy that can use the ‘scope better than you).

T&M is undergoing another renaissance, as it must whenever industry goes through any disruptive change. You can only test a system with a device that has a higher resolution/speed/capacity than the one being tested. In other words, if your ruler lines aren’t smaller than the features on what you are trying to measure, you will only be as precise as those markings.

This requirement is exacerbated by the nowadays (actually always) need to test at almost every stage of development and production. It is almost impossible to attain six-sigma reliability without intelligent oversight at every step, from the bench to the box. That means everyone in the process must have (and use properly) test equipment that is accurate, fast, and functional. This can get expensive, obviously. This cost issue is also a barrier for small shops that may only need one device, but can’t afford the latest bells-and whistles machine.

The good news is that the same advances that are driving electronic product development are also impacting the T&M space. High instrument integration enables compact form factors and the ability to create a competitive system for the average user at a price they can afford. One example of this trend can be found in the Rohde & Schwarz RTC1000 oscilloscope series. Directly addressing the need for a highly functional cost-effective T&M device, this compact eight-in-one instrument can act as an eight-channel logic analyzer, a four-channel pattern generator, and a protocol analyzer for I2C, SPI, UART/RS-232, CAN, and LIN, as well as a digital voltmeter, component tester, spectrum analyzer, and counter. Available in models from 50 MHz to 300 MHz, they offer bandwidth upgrades via software license all the way to 300 MHz bandwidth. The two-channel oscilloscopes have maximum sample rates of 2 Gsample/s and a memory depth of 2 Msample. All models come as standard with LAN and USB interfaces.

Figure 2. The RTA4000 series is also ideal for analyzing serial protocols, with an acquisition memory depth up to 1 Gsample.

This convergence also enables more functionality to be put into larger systems as well. For example, to serve more professional users with greater needs, Rohde & Schwarz used the same integrated approach to create the RTM3000 and RTA4000 series, with 10-bit vertical resolution to enable power measurement that fulfills the stringent requirements demanded by advanced electronics development. Operating with bandwidths of 100 MHz, 200 MHz, 350 MHz, 500 MHz, and 1 GHz, the RTM3000 oscilloscope has a 5 Gsample/s 10-bit ADC, with 40 Msample (80 Msample interleaved) per channel acquisition memory (with an optional 400 Msample segmented acquisition memory), and the RTA4000 oscilloscope offers bandwidths of 200 MHz, 350 MHz, 500 MHz, and 1 GHz. The RTA4000 is also suited for analyzing serial protocols, with an acquisition memory depth up to 1 Gsample, and the same 10-bit ADC, but with even more memory and a 100 Msample (200 Msample interleaved) per channel acquisition memory, and standard 1 Gsample (1,000 Msample) segmented acquisition memory.

Power measurements, such as ripple and noise measurements of a DC line, demand an oscilloscope with high vertical resolution, low noise and excellent DC gain linearity. The 10-bit ADCs of the RTM3000 and RTA4000 series support 1024 vertical positions, 4x better than legacy 8-bit oscilloscopes, and essential for ripple and noise measurements. While the R&S RTM3000 series comes in two- and four-channel models, the R&S RTA4000 series oscilloscopes are exclusively four-channel models.

The expanding demand for compact, highly efficient switched-mode power supplies, inverters, and electric drives demands the use of leading-edge semiconductors and components, creating new challenges for T&M equipment. It doesn’t help to have great bench T&M gear if your probes aren’t able to deliver good, clear, and precise information to the device. One example of how companies are addressing this need is the new family of high-voltage differential probes from Rohde & Schwarz, that enable measurements with extremely high signal integrity. The RT-ZHD high-voltage differential probes are well suited for measurements on modern power semiconductors, and with a bandwidth of up to 200 MHz, they can even measure very fast switching edges. The four models have maximum peak voltages from 750 V to 6000 V, and exhibit excellent common-mode rejection across the entire frequency range that effectively suppresses fast-switching common mode signals. With an integrated offset compensation that operates independently of probe attenuation and the oscilloscope’s vertical settings, they can measure very small ripple voltages with a large DC component. With an offset compensation of up to 2000 V, they cover a very large range of measurement applications, and have a DC measuring accuracy of ± 0.5 percent. The probes also feature an integrated ProbeMeter that measures DC offset with ± 0.1 percent accuracy, with the readings displayed directly on the oscilloscope.The RT-ZHD probes also use high levels of internal system integration to help eliminate erroneous readings, and enable the oscilloscope to automatically recognize the configured attenuation factor and other probe settings to display the correct voltages and reliably detect incidents such as overvoltage. Probe functions can also be accessed via the SCPI remote control interface, making the probes a good choice for automated tests as well.

Figure 3. The RT-ZHD probes use high levels of internal system integration to help eliminate erroneous readings.

Two other examples are the R&S RT-ZD002 and R&S RT-ZD003 differential probes with maximum input voltages up to 700 V and 1400 V, respectively. These 25 MHz probes boast very low inherent noise for their class of around 7 mV (RMS) and 14 mV (RMS), respectively. Their BNC interface makes them a perfect fit for R&S RTC1000, R&S RTB2000 and all standard oscilloscopes.

The pressures of T&M on the electronics engineer will never go away, as the field is caught up in a perpetual “Red Queen’s Race” of constant change as T&M devices strive to stay ahead of the embedded systems they are testing. The latest highly-integrated cost-effective devices available today can help you stay ahead of the pack.


Related


The Benefits of C and C++ Compiler Qualification

In embedded application development, the correct operation of the compilation toolset is critical to the functional safety of the application. Two options are available to build trust in the corre...

An introduction to the SuperTest MISRA suites

The SuperTest MISRA suites are created to verify the conformance of MISRA checking software. The aim of a, so-called, MISRA checker is to check application software for its compliance with the MIS...

8 Ways to Improve Harness Manufacturing

Harness manufacturing is a low margin business where quality, accuracy, and speed are essential to success. It can benefit from a full, automated and digitally continuous flow from product design to h...

General principles of PCBs design

How to design PCBs correctly, to reach boards which are cost-effective to produce and to populate? Which are the most important PCB design principles? What about production technology of PCB? We have ...

The Next Level of Embedded Software Development

With the rapid expansion of complex technology into everyday life, the importance of software is growing exponentially. This complimentary webinar presented by Siemens PLM Software will show how emb...

Embedded Software for Safety Critical Applications

Production code generation with Model-Based Design has replaced document-based development and manual coding in various domains in automotive, industrial automation, aerospace and medical. Safety-rela...

Coding safe and secure applications

The debate about safety and security concerns in high integrity software applications is a hot topic of discussion in modern software management. The need to address these concerns is present in e...

Best practices for static analysis tools

This paper reviews a number of the growing complexities that embedded software development teams are facing, including the proliferation of third-party code, increased pressures to develop secure ...


Give Your Product a Voice with Alexa

Join us for a deep dive into the system architecture for voice-enabled products with Alexa Built-In. Device makers can use the Alexa Voice Service (AVS) to add conversational AI to a variety of produc...

The two big traps of code coverage

Code coverage is important, and improving coverage is a worthy goal. But simply chasing the percentage is not nearly so valuable as writing stable, maintainable, meaningful tests. By Arthur Hick...

Securing the smart and connected home

With the Internet of Things and Smart Home technologies, more and more devices are becoming connected and therefore can potentially become entry points for attackers to break into the system to steal,...

Accurate and fast power integrity measurements

Increasing demands on power distribution networks have resulted in smaller DC rails, as well as a proliferation of rails that ensure clean power reaches the pins of integrated circuits. Measuring r...

 

Arrow and Analog Devices strategic partnership and collaborative approach to provide solutions for our customers.

Mike Britchfield (VP for EMEA Sales) talks about why Analog Devices have a collaborative approach with Arrow Arrow’s design resources are key, from regional FAEs in the field to online des...


WE MAKE IT YOURS! Garz & Fricke to present the latest HMIs and SBCs at Electronica 2018

Sascha Ulrich, Head of Sales at Garz & Fricke, gives you a quick overview about the latest SBC, HMI and Panel-PC Highlights at electronica 2018. Learn more about the SANTOKA 15.6 Outdoor HMI, the ...


Macronix Innovations at electronica 2018

Macronix exhibited at electronica 2018 to showcase its latest innovations: 3D NAND, ArmorFlash secure memory, Ultra Low Vcc memory, and the NVM solutions with supreme quality mainly focusing on Automo...


ams CEO talks about their sensor solutions that define the mega trends of the future

In this video Alexander Everke, ams’ CEO, talks to Alix Paultre of EETimes about their optical, imaging and audio sensor solutions in fast-growing markets – from smartphones, mobile device...


Intel accelerated IoT Solutions by Arrow

Arrow is showing Intel’s Market Ready Solutions in a Retailer shop with complete eco environment. From sensors via gateways into the cloud, combined with data analytics, the full range of Intel ...


CSTAR - Manufacturers of cable assembly from Taiwan

CSTAR was founded in 2010 in Taipei, Taiwan. Through years of experience, we are experts in automotive products, LCD displays, LCD TVs, POS, computers, projectors, laptops, digital cameras, medical ca...


NXP Announces LPC5500 MCU Series

Check this video to discover the new NXP microcontroller LPC5500, the target application and focus area. Links to more information: LPC5500 Series: World’s First Arm® Cortex® -M...


Molex Meets Solutions at Electronica

These are exciting times in the electronics world as Molex migrates from a pure connectors company to an innovate solutions provider. Solutions often start at the component level, such as the connecto...


Alix Paultre investigates Bulgin's new optical fiber rugged connector range at Electronica 2018

Alix Paultre interviews Bulgin's Engineering Team Leader Christian Taylor to find out more about the company's new range of optical fiber connectors for harsh environments. As the smallest rug...


Cypress MCU and Connectivity are the best choice for real-world IoT solutions.

Cypress’ VP of Applications, Alan Hawse, explains why people should use Cypress for their IoT connectivity and MCU needs. Cypress wireless connectivity and MCU solutions work robustly and sea...


Chant Sincere unveils their latest High Speed/High Frequency connection solutions at Electronica 2018

Chant Sincere has been creating various of product families to provide comprehensive connection solutions to customers. USB Series Fakra Series QSFP Series Metric Connector Series Fibro ...


Addressing the energy challenge of IoT to unleash billions of devices

ON Semiconductor introduces various IoT use cases targeted towards smart homes/buildings, smart cities, industrial automation and medical applications on node-to-cloud platforms featuring ultra-low po...


ITECH, world leading manufacturer of power test instruments, shinned on electronica 2018

ITECH, as the leading power electronic instruments manufacturer, attended this show and brought abundant test solutions, such as automotive electronics, battery test, solar array simulator, and electr...


ITECH new series give users a fantastic user experience

ITECH latest series products have a first look at the electronics 2018, such as IT6000B regenerative power system, IT6000C bi-directional programmable DC power supply, IT6000D high power programmable ...


SOTB™ Process Technology - Energy Harvesting in Embedded Systems is Now a Reality

Exclusive SOTB technology from Renesas breaks the previous trade-off between achieving either low active current or low standby current consumption – previously you could only choose one. With S...


E-Mail Newsletters

nlsc240

Our 3 E-Mail Newsletters: EETimes/EDN Europe, Embedded News and Power Electronics News inform about the latest news in technology and products, as well as technical know-how like white papers, webinars, articles, etc.


B & S / ECE Magazine

- latest issue is online now -

November 2018

Content Highlights

Cover Story

Internet-connected displays make the industrial IoT more visible

Download now